step 2Find the Chip

step 2Find the Chip

In this instructable, I am using an old, deactivated debit card. I found the RFID chip in a previous card by cutting into it randomly.
I DO NOT recommend this method if you don't know where the chip is, as you could obviously damage the chip and make it unusable.
I do not know if all cards are setup with the RFID in the same location, but if they are, my guidelines will give you a good idea where to start.

If not, I was able to see the impression of the chip on the back of the card when I looked at it from an angle in a well lit room (it appeared as a small square impression only a few millimeters across).

Make sure to mark out a guideline to cut along that goes from the bottom of the magnetic strip to the top of the imprinted card numbers. This will yield a decent size chunk of the card with the RFID in the center

How to turn your cellphone into a credit/debit card

introHow to turn your cellphone into a credit/debit card

Easy to do mod for an extra credit/debit card with RFID chip (i.e. Paypass).

Using this method, you will be able to locate and extract the RFID chip in your spare
Paypass-capable card and place it in your cellphone. This will allow you to present your cellphone at Paypass terminals (movie theaters, McDonalds, etc..) and pay using the RFID chip.

step 4How to kill your RFID chip

step 4How to kill your RFID chip

In this step I will describe a few ways to permanently disable or kill an RFID chip. Most products that you own that contain RFID tags belong to you, so you have the right to destroy them; however, tampering with a US passport is a federal offense. Luckily there are ways to kill an RFID tag without leaving any evidence, so as long as you are careful, it would be pretty hard to prove that you did anything illegal.


-The easiest way to kill an RFID, and be sure that it is dead, is to throw it in the microwave for 5 seconds. Doing this will literally melt the chip and antenna making it impossible for the chip to ever be read again. Unfortunately this method has a certain fire risk associated with it. Killing an RFID chip this way will also leave visible evidence that it has been tampered with, making it an unsuitable method for killing the RFID tag in passports. Doing this to a credit card will probably also screw with the magnetic strip on the back making it un-swipeable.

-The second, slightly more convert and less damaging, way to kill an RFID tag is by piercing the chip with a knife or other sharp object. This can only be done if you know exactly where the chip is located within the tag. This method also leaves visible evidence of intentional damage done to the chip, so it is unsuitable for passports.

-The third method is cutting the antenna very close to the chip. By doing this the chip will have no way of receiving electricity, or transmitting its signal back to the reader. This technique also leaves minimal signs of damage, so it would probably not be a good idea to use this on a passport.

-The last (and most covert) method for destroying a RFID tag is to hit it with a hammer. Just pick up any ordinary hammer and give the chip a few swift hard whacks. This will destroy the chip, and leave no evidence that the tag has been tampered with. This method is suitable for destroying the tags in passports, because there will be no proof that you intentionally destroyed the chip.

step 3How to block a RFID tag

step 3How to block a RFID tag

Luckily RFID tag signals can easily be blocked. This means that you will have the option to use the tag whenever you want, and prevent others from being able to read it.

The signal sent out by a RFID tag is easily blocked by metal. This means that placing the RFID tag inside of a Faraday cage will prevent the information from being read.

There are already two Instructables on how to build RFID blocking containers:

RFID Secure Wallet

Make a RFID Shielding Pouch Out of Trash

Or if you would rather spend money on something you could build, head over to Think Geek for their RFID blocking wallet and RFID blocking Passport Holder .

step 1Reasons for blocking / destroying RFID chips

step 1Reasons for blocking / destroying RFID chips

The main reason someone would want to block or destroy RFID chips would be to maintain privacy. In the last step I explained that RFID tags can be read from very long distances. The potential for abuse of this technology grows as more and more products and devices are being created with these tags built in.

Companies are getting consumers to blindly accept many RFID tagged products with the promise of convenience; however, most of the devices that contain RFID tags don't really need them. The tags may save a few seconds, but sacrifice an enormous amount of privacy and security. It is now possible for someone, with relatively simple equipment, to walk down a busy sidewalk and pickup the personal information of people carrying RFID tagged devices, without them even knowing.

Being able to block or destroy these chips allows people to decide what type of information they are willing to sacrifice for convenience.

VeriChip's "Hugs" Infant Protection System

by Donald Melanson

Information Week reports that VeriChip's RFID-based "Hugs" Infant Protection System sounded an alarm last week when the parents of an infant tried to take their baby out of the hostipal without authorization—security officials were then able to stop the parents before they were able to leave the hostipal with the baby. It's not clear if this is the first time the system was succesfully used or not, but it's currently deployed in some 900 hostipals in the U.S. In addition to preventing abductions, it's also designed to prevent accidental mismatchings. Man, they're totally wrecking on the premises for future Disney kids films, dude—the switched at birth plot device is like, classic.